Yea, it's been a while - but there's been progress!

I haven't made time to update the blog in about 5 months... Things have been crazy, to say the least... I took about two months off (May & June) and since then what little time I've had I've spent working as opposed to writing.

Since the last update a lot has been accomplished. The foundation underpinning is complete, the floor has been poured, I've framed out the room and two closets, re-ran several electrical circuits, removed about 40' of old metal ductwork and replaced it with insulated flex ductwork, insulated the walls and ceiling, hung sheetrock, and started to tape & spackle.

Here are some pic's:

Wow, no more dirt !!! The 4x6 Pressure treated header has been replaced by a pair of 20' 2x6" Microlam joists. These are about 10x stronger than what I had there temporarily and will never bend, warp, or bow since it's a manufactured plywood and I've essentially "overdoneit" with lolly columns. : )

Here's my little helper - Ricky. He's a great sweeper by the way, much better than I in fact. Must be because he's closer to the ground, right?

70 2x4x8's, water seal for the walls, and various waterproof concrete formulas to seal the cracks in the existing foundation. The walls are starting to go up too:

This iteration now shows some hi-hat lights, insulation, and flex-ducts:

Since removing the metal duct work for which has been the culprit for many of the scars on my balding head, I needed to re-feed three registers and add a new one for the new room. Due to space limitations, I couldn't run four flex ducts back to the air handler, so I built a distribution box and fed it with two ducts from the air handler. Air flow hasn't always been that great in this house to begin with, so any deviation wouldn't be really be noticed.

I'm using green-board (bathroom board) which is mold and mildew resistant for the bottom portion of the walls. I figure that if I ever get water in the basement, at least the sheetrock won't have to be torn out due to mold growth on the paper. After thinking about it, I should've used green board on the upper walls and ceiling too as humidity levels can promote mold growth, but it is what it is... Besides, there is no way that I am lugging 20 pieces of sheetrock back up those stairs - getting it down was tough enough!

Stay tuned - more pics to come...

Caution: Wet Concrete!

Ok, that time has come. The time for concrete to be poured is now. Here are some pics:

Below is a pic of some forms that were erected to contain and essentially "form" the new retaining wall and underpinning of the existing foundation wall. What you see straight on is the retaining wall which has forms on both sides held together by steel pins and what you see on the right that is supported by all of those 2x4's is the underpinning. The underpinning only has a form on one side and it is necessary to support it with 2x4's like such as the weight of the concrete can very well push the form away from the foundation and spill.

Now the pic above represents nearly 1/3 of the work that needs to be complete. When underpinning, it's important "NOT" to do everything at once otherwise you risk a total cave-in. So, we're are doing one corner with 6' of underpinning, we'll do the other corner with 6' of underpinning, then will mend the middle 6' between the two ends. The last bit of concrete work will involve pouring the floor.

Below represents the retaining wall that has forms on both sides. This leads perpendicularly to the existing foundation wall and underpinnings:

What you see below is the other end of the pic from above, essentially the T section where the retaining wall meets the existing foundation wall:

What you see below is where the new concrete replaces the area of the existing footing that had fallen free. This way the footing is repaird and the work is continuious through the room and provides the same structural integrity throughout:

What you see below represents the remaining dirt that needs to be removed and the footings that require underpinning (the other 2/3).

Two weeks & 24,000 lbs of soil.

We've had a very busy couple of weeks working on the project. In the past two weeks, I've logged about 40 hours of work between working full days on weekends and putting in an hour or two here and there after work. Each week we've stored around 4 cubic yards.

(How much does a yard of soil weigh? A yard weighs in at 1.5 tons or 3000lbs. (1.5 x 4 = 6 ton's x 2 = 12 tons))

A week ago this past Saturday, Mike & I dug, filled, and humped 130 buckets of soil while also taking down the far end of the concrete wall - yes, all in one day.

This past week, Mike & I dug, filled, and humped around 120 buckets of soil, stone, and concrete debris. I was able to dig a pair of pits (4' round x 4' deep) so that I can bury some rather large boulders. (300+ lbs each) (Put it this way, these stones were so large it took me nearly an hour to dig each hole and undermine the boulders so that they would roll into the pits for burial.)

This past weekend we were able to build a form for a lally column footing (16"x16"x16") using 5000psi concrete with wire mesh and rebar for reinforcement. I created a template out of cardboard to mimick the base plate of the lally column. I placed four 5/8" Jbolts through the template and set their height using the 5/8" nuts. This template served two purposes - 1) the proper alignment of bolts so that when the concrete is dry, the bolts will be in the correct position for mounting of the lally column, and 2) to keep the bolts from sinking into the 16" of concrete.

This evening we placed the new 4"x6" pressure treated header into place. It looks like we're getting somewhere now...

Here's some pics:

1 Man + 1 Sledge Hammer = a Big Pile of Rocks

Yesterday was spent swinging a 16lb sledge hammer with fury taking down the far end of the old foundation wall. Some field stones were so large that I could barely budge them, so I was forced to split them. Here's some pics. Enjoy my insanity:





This one shows that the pile is nearly 4' tall. (Count the steps.)



Here's whats left of the far side of the wall - the picture was taken from within the escavated area.



Here are some shots of my my now one legged Circuit Breaker Panel:

Chapter Three

It's been a few weeks since my past post as things have been pretty busy with work. Despite being plaged at the office, we've been able to get a considerable amount of work done though.

Ok, we all know that digging dirt, filling buckets with said dirt, and humping it up out of the basement isn't exactly exciting stuff, but that's pretty much the jist of what's been done.

Here are some pics:

Yours truly:

Meet Mike, my neighbor who's been good enough to lend me his heavy duty trailer that can hold about 2 Yards of soil (rougly 5400lbs) as it's rated for 2.5 tons (5600lbs). He's also been helping out (digging & humping buckets to his trailer). I've struck a deal with him in that he'd get paid by volume. ($100/yard.) After all is said and done, I figured that I had about 25 yards worth of soil, stone, & concrete to move - so he stands to make around $2500 for his time and energy.)

I've installed a few temporary lolly columns (in an overkill capacity) to make sure that the house doesn't settle and crackle my spackle in the dining room above.

Here are some pics that illustrate the new lolly columns in use (supporting the house) and the twisted 2x6's that are essentially now unsupported in the far half:

Stay tuned, as there's more to come. Same Bat time, same Bat channel.